Sign In | Join Free | My chinacsw.com
China Guang Zhou Lai Jie Electric Co.,Ltd logo
Guang Zhou Lai Jie Electric Co.,Ltd
Guang Zhou Lai Jie Electric Co.,Ltd
Site Member

8 Years

Home > TAMAGAWA >

TAMAGAWA TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63

Guang Zhou Lai Jie Electric Co.,Ltd

TAMAGAWA TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63

Place of Origin : Japan

Brand Name : Tamagawa

Certification : CE

Model Number : TS5013N63

MOQ : 1pcs

Payment Terms : T/T, Western Union, , MoneyGram

Supply Ability : 100pcs/week

Delivery Time : in stock

Packaging Details : carton

TAMAGAWA : TAMAGAWA

Material : iron

color : black

Japan : Japan

wire : wire

temperature : 20-90

dimension : 80mm

TS5013N63 : TS5013N63

Contact Now

TS5013N63

TAMAGAWA TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63TAMAGAWA TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63TAMAGAWA TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63TAMAGAWA TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63

he RTD module needs to have the current loop continuous to eliminate extra stabilization
time which is automatically added to an unused channel that is not deactivated.
hen 500 Ω and 1000 Ω RTD ranges are used with other lower value resistors, the error
may increase to two times the specified error.
For
consistency the RTD module should have a resistor connected (like the 2-wire RTD
connection)The module reports 32767 on any activated channel with no sensor connected. If open wire
Best accuracy will be achieved for the 10 Ω RTD ranges if 4 wire connections are used.
The resistance of the connection wires in 2 wire mode will cause an error in the sensor
detection is also enabled, the module flashes the appropriate red LEDs. reading and therefore accuracy is not guaranteedAfter power is applied, the module performs internal calibration for the analog-to-digital

Guang Zhou Lai Jie Electric Co.,LTD

Please contact with “Tommy” for the price

TS3636N6

TS-5170-N20

TS5208N530

TS4503N1007E200

TS3092N11E12

AU6550N2062

TS3664N1E1

TS3617N1E3

TS3641N1E1

TS5207N530

TS5208N569

TS4503N1022E100

TS3095N2

AU6649N2101

TS3664N1E2

TS3630N1214E3

TS3641N21E6

TS5208N510

TS5208N576

TS4503N1022E200

TS3103N156

FACODER

TS3664N2E3

TS5013N60

TS3641N22E7

TS5208N68

TS5210N450

TS4503N1202E200

TS3103N178

TS3664N2E4

TS5013N61

TS3641N2E3

TS5212N351

TS5210N453

TS4503N1205E200

TS3103N255

TS3664N50

TS5016N60

TS3641N12E3

converter. During this time the module reports a value of 32767 on each channel until valid
data is available on that channel. Your user program may need to allow for this initialization
time. Because the configuration of the module can vary the length of the initialization time,
you should verify the behavior or the module in your configuration. If required, you can
include logic in your user program to accommodate the initialization time of the moduleTo maintain module resolution and accuracy when the 400 Hz filter is selected, the integration time is 10 ms. This
selection also rejects 100 Hz and 200 Hz noiseWhen switching frequencies above 20 kHz, it is important that the digital inputs receive a
square wave. Consider the following options to improve the signal quality to the inputs:
 Minimize the cable length
 Change a driver from a sink only driver to a sinking and sourcing driver
 Change to a higher quality cable
 Reduce the circuit/components from 24 V to 5 V
 Add an external load at the input Because both sinking and sourcing configurations are supported by the same circuitry, the active state of a sourcing
load is opposite that of a sinking load. A source output exhibits positive logic (Q bit and LED are ON when the load has
current flow), while a sink output exhibits negative logic (Q bit and LED are OFF when the load has current flow). If the
module is plugged in with no user program, the default for this module is 0 V, which means that a sinking load will be
turned ON. Because both sinking and sourcing configurations are supported by the same circuitry, the active state of a sourcing
load is opposite that of a sinking load. A source output exhibits positive logic (Q bit and LED are ON when the load has
current flow), while a sink output exhibits negative logic (Q bit and LED are OFF when the load has current flow). If the
module is plugged in with no user program, the default for this module is 0 V, which means that a sinking load will be
turned ON. When switching frequencies above 20 kHz, it is important that the digital inputs receive a
square wave. Consider the following options to improve the signal quality to the inputs:
 Minimize the cable length
 Change a driver from a sink only driver to a sinking and sourcing driver
 Change to a higher quality cable
 Reduce the circuit/components from 24 V to 5 V


Quality TAMAGAWA TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63 for sale

TAMAGAWA TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63 TS5013N63 Images

Inquiry Cart 0
Send your message to this supplier
 
*From:
*To: Guang Zhou Lai Jie Electric Co.,Ltd
*Subject:
*Message:
Characters Remaining: (0/3000)
 
Inquiry Cart 0